Re: [PATCH 3/3] OvmfPkg/PlatformPei: Mark TPM MMIO range as unencrypted for SEV

Lendacky, Thomas

On 4/23/21 8:04 AM, Laszlo Ersek wrote:
On 04/23/21 12:26, Laszlo Ersek wrote:
review#2 from scratch:

On 04/21/21 00:54, Tom Lendacky wrote:
From: Tom Lendacky <>


The TPM support in OVMF performs MMIO accesses during the PEI phase. At
this point, MMIO ranges have not been marked un-encyrpted, so an SEV-ES
guest will fail attempting to perform MMIO to an encrypted address.
(1) As discussed, please update the commit message, for more clarify
about SEV vs. SEV-ES.

Read the PcdTpmBaseAddress and mark the specification defined range
(0x5000 in length) as un-encrypted, to allow an SEV-ES guest to process
the MMIO requests.

Cc: Laszlo Ersek <>
Cc: Ard Biesheuvel <>
Cc: Jordan Justen <>
Cc: Brijesh Singh <>
Cc: James Bottomley <>
Cc: Jiewen Yao <>
Cc: Min Xu <>
Signed-off-by: Tom Lendacky <>
OvmfPkg/PlatformPei/PlatformPei.inf | 1 +
OvmfPkg/PlatformPei/AmdSev.c | 19 +++++++++++++++++++
2 files changed, 20 insertions(+)

diff --git a/OvmfPkg/PlatformPei/PlatformPei.inf b/OvmfPkg/PlatformPei/PlatformPei.inf
index 6ef77ba7bb21..de60332e9390 100644
--- a/OvmfPkg/PlatformPei/PlatformPei.inf
+++ b/OvmfPkg/PlatformPei/PlatformPei.inf
@@ -113,6 +113,7 @@ [Pcd]

+ gEfiSecurityPkgTokenSpaceGuid.PcdTpmBaseAddress
diff --git a/OvmfPkg/PlatformPei/AmdSev.c b/OvmfPkg/PlatformPei/AmdSev.c
index dddffdebda4b..d524929f9e10 100644
--- a/OvmfPkg/PlatformPei/AmdSev.c
+++ b/OvmfPkg/PlatformPei/AmdSev.c
@@ -141,6 +141,7 @@ AmdSevInitialize (
UINT64 EncryptionMask;
+ UINT64 TpmBaseAddress;

@@ -206,6 +207,24 @@ AmdSevInitialize (

+ //
+ // PEI TPM support will perform MMIO accesses, be sure this range is not
+ // marked encrypted.
+ //
+ TpmBaseAddress = PcdGet64 (PcdTpmBaseAddress);
+ if (TpmBaseAddress != 0) {
It's OK to keep this as a sanity check, yes.

+ RETURN_STATUS DecryptStatus;
+ DecryptStatus = MemEncryptSevClearPageEncMask (
+ 0,
+ TpmBaseAddress,
+ EFI_SIZE_TO_PAGES (0x5000),
(2) Should be (UINTN)0x5000, as discussed earlier.

+ );
+ ASSERT_RETURN_ERROR (DecryptStatus);
(3) So this is where the mess begins.

The idea is to delay the dispatch of Tcg2ConfigPei until after
PlatformPei determines if SEV is active, and (in case SEV is active)
PlatformPei decrypts the MMIO range of the TPM.

For this, we need to change the IA32 / X64 DEPEX of Tcg2ConfigPei, from
the current TRUE, to some PPI GUID.

There are two choices for that PPI:

(a) gEfiPeiMemoryDiscoveredPpiGuid


- no new PPI definition needed,

- no new PPI installation needed,

- OvmfPkg/Bhyve/PlatformPei needs no separate change


- total abuse of gEfiPeiMemoryDiscoveredPpiGuid

(b) gOvmfTpmMmioAccessiblePpiGuid


- this new GUID must be defined in "OvmfPkg.dec", in the [Ppis] section,
in a separate patch; its comment should say "this PPI signals that
accessing the MMIO range of the TPM is possible in the PEI phase,
regardless of memory encryption". The PPI definitions should be kept
alphabetically ordered.

- OvmfPkg/PlatformPei must install this new PPI, with a NULL interface.
(See "mPpiBootMode" as a technical example.) OvmfPkg/PlatformPei must
install this new PPI either when the SEV check at the top of
AmdSevInitialize() fails, or when MemEncryptSevClearPageEncMask() succeeds.

- OvmfPkg/Bhyve/PlatformPei must receive the same update, in a separate
patch. That's because "OvmfPkg/Bhyve/BhyveX64.fdf" includes the same
"Tcg2ConfigPei", but consumes "OvmfPkg/Bhyve/PlatformPei" rather than
"OvmfPkg/PlatformPei". Tcg2ConfigPei will receive the same
stricter-than-before depex, so something on the bhyve platform too must
produce the new PPI.


- more or less palatable as a concept, with the new PPI precisely
expressing the dependency we have.

In approach (b), the "OvmfPkg/Bhyve/PlatformPei" patch needs to be CC'd
to the Bhyve reviewers. If the Bhyve reviewers determine that such an
update is actually unnecessary, because on Bhyve, there is no TPM
support and/or no SEV support in fact, then *first* we have to create an
independent Bhyve cleanup series, that rips out the TPM and/or SEV
remnants from the OvmfPkg/Bhyve sub-tree.

I prefer approach (b). I'm sorry that it means extra work wrt. Bhyve,
but I strongly believe in keeping all platforms in the tree, and that
means we need to spend time on such changes.

I'm not CC'ing Rebecca and Peter on this message -- we're deep into this
patch review thread, and they'd have no useful context. I suggest simply
including the "OvmfPkg/Bhyve/PlatformPei" patch in the next version of
this series, with a proper explanation in the blurb (patch#0) and on the
"OvmfPkg/Bhyve/PlatformPei" patch. That should give them enough context
to evaluate whether the change is necessary, or whether we should purge
the TPM and/or the SEV bits from Bhyve. You could also ask them just
this question in advance, in a separate email on the list (with
distilled context). Personally I'm unsure if the TPM and SEV bits
survived into Bhyve because those bits are actually put to use there, or
because the initial platform creation / cloning wasn't as minimal as it
could have been.

Note that in case TPM makes sense on bhyve but SEV doesn't, then
"OvmfPkg/Bhyve/PlatformPei" will have to install the new PPI
I've had a further idea on this.

You could add an entirely new PEIM just for this. The entry point
function of the PEIM would check for SEV, decrypt the TPM range if SEV
were active, and then install gOvmfTpmMmioAccessiblePpiGuid
(unconditionally). The exit status of the PEIM would always be
EFI_ABORTED, because there would be no need to keep the PEIM resident.

The new PEIM would have a DEPEX on gEfiPeiMemoryDiscoveredPpiGuid, to
make sure that potential page table splitting for the potential MMIO
range decryption could be satisfied from permanent PEI RAM.

The new PEIM would be included in the DSC and FDF files of the usual
three OVMF platforms, and in the Bhyve platform -- dependent on the
TPM_ENABLE build flag.

There are several advantages to such a separate PEIM:

- For Bhyve, the update is minimal. Just include one line in each of the
FDF and the DSC files. No need to customize an existent
platform-specific PEIM, no code duplication between two PlatformPei modules.

- The new PEIM would depend on the TPM_ENABLE build flag, so it would
only be included in the firmware binaries if and only if Tcg2ConfigPei
were. No useless PPI installation would occur in the absence of TPM_ENABLE.

- No need to check PcdTpmBaseAddress for nullity in the new PEIM, before
the decryption, as TPM_ENABLE guarantees (on IA32/X64) that the PCD
already has the right value.

- The new logic would be properly ordered between PlatformPei and
Tcg2ConfigPei, namely due to the use of two such PPI GUIDs in DEPEXes
that actually make sense. PlatformPei -> TPM MMIO decryptor PEIM ordered
via "memory discovered" (needed for potential page table splitting), TPM
MMIO decryptor PEIM -> Tcg2ConfigPei ordered via "TPM MMIO decrypted".

You could place the new PEIM at:


If you haven't lost your patience with me yet, I'd really appreciate if
you could investigate this!
So far, this appears to be working nicely. I'm new at the whole PEIM
thing, so hopefully I haven't missed anything. I should be submitting the
patches soon for review.

One thing I found is that the Bhyve package makes reference to the
OvmfPkg/Bhyve/Tcg directory, but that directory does not exist. So I don't
think that TPM enablement has been tested. I didn't update the Bhyve
support for that reason.



Join to automatically receive all group messages.